Powersportswraps.com is excited to show you one of our all-new 2014 Honda Grom MSX 125 Graphics Kits. The Dirty Air Craft Metal P40 Shark Face Grom decal kit (pictured) consists of more than 17 pre-cut decals precision fit for the Grom body panels. These easy-to-apply graphics are produced on the air-release wrapping film with cast sheet laminate to protect the image surface from scratches, scuffs & UV rays. This means that your graphic image is a sub surface image that is protected under the laminate for years of durability. With the re-positional Grom graphic film, installing this custom Honda MSX 125 decal kit is a breeze. Just peel and stick it to apply! Not sure how to apply our graphics? Watch our Grom Graphics kit installation video here.
See Powersportswraps current selection of 2014 Honda MSX 125 Grom graphics here. More Honda Grom decal kits being created each and every day so keep checking the site for the latest Honda Grom vinyl decal sets.
If you have a decal kit idea be sure to send us your concept so we can provide an estimate to custom create your own personal decal kit.
This custom bike wrap was done for one of our customers all the way from Soul Korea. Terry Washington shipped us all the parts off his ZX-7 Kawasaki & told us to have some fun. He choose our Confusion Lime Green wrap pattern for the base effect & told us to incorporate some checker flag with it. As you can see the bike came out great!! We even incorporated custom ZX-7 emblems on the tail section for him. Once we had the custom sport bike vinyl wrap applied to his bike parts we carefully boxed them back up & shipped them back to Korea.
If you would like to do a custom wrap on your motorcycle but do not want to attempt the install, contact us we can help.. We can apply your wrap pattern of choice to the parts & then send them back once completed.
Terry Said: I get tons of compliments every time I ride! They always me ask” who did your paint”? When I tell them it’s vinyl, they’re shocked! I point out your companies name and web page and I also tell them to go to Youtube and watch how you guys wrapped the black bike. Again, I can’t begin to thank you enough. Hope you like the pics and feel free if you want to add any of these to your site.
This is Mike Burke’s 1985 BMW K100 with our Blue-Black Flame wrap applied on it. Mike is a very meticulous guy who wanted a different look for his BMW. He contacted us with a special request flame wrap that we had to design for him. Each panel of this BMW was measured by Mike & he told us which sheet of ours that he wanted to use. With a bit of time and effort we edited the sheets to meet his requirements & provided proofs prior to production just to be sure he was getting what he wanted.
To Order your Custom do it yourself vinyl wrap
Mike’s Personal Comments:
First I would like to thanks the staff of Power Sports Wraps for the time they spent to altering the standard pattern to fit the specific dimensions of my vehicle. I also must confess that I did not install the graphic on the upper fairing, I paid a professional for that part as I had been working on this for 2 weeks and simply wanted it to be finished. Except for the gas tank, I installed the graphic without assistance on the rest of the bike. With that experience in mind, I do not recommend trying to do this alone unless the parts are securely held during the application. Patients is a requirement as it can take several hours to complete a single piece depending on the complexity of the part being covered. My bike had some white spray paint on a few of the surfaces. This created an adhesion problem. After encountering this issue, I used a green scrubbing pad and removed some of the white paint. This seems t o have reduced the tendency of the vinyl to lift the paint off the surface during the application process. Four pieces of black vinyl have been installed on what will be the horizontal surfaces. Be careful with these inside angles, if the vinyl is stretched too much, it may not adhere to the surface, creating the appearance of a bubble. It took me about 12 tries to figure out how to cover this area properly, (I’m probably just a slow learner).The front fender had its own challenge. I ended up with excessive vinyl overlapping near the midpoint of the fender. I decided to solve this by cutting and overlapping where the front fork would hide the fix. Then I removed the patterned vinyl and covered the area with black vinyl.Since I was working alone, I chose to remove the backing of the vinyl sheet only as it became necessary during the application.
The gas tank was also a problem. Perhaps if I had more helpers, (or more experience), it would have turned out differently. I had to make a cut and overlap on the side of the tank. Not very noticeable in the pic, but I may cover it with a narrow piece of black eventually.
I did try using the black vinyl for the mirrors, but in the end decided to go with a can of spray paint and some rubbing compound. Eleven separate parts were covered with vinyl, and there are some small defects in the surface, (even of the piece I paid for), but none of the defects are obvious to the casual observer. In fact, the worst are in places not visible to a standing observer. I am quite pleased with the results. Mike Burke
This P40 Warhawk sport bike wrap can be created using our Dirty Aircraft Metal vinyl wrapping film by the sheet & our all new Flying Tigers Shark Face element. Each item is a peel & stick application so you can create the look you want. Do it yourself vinyl wraps are our specialty, mix & match a variety of films for your own custom bike wrap look. As you see in the photo we also applied our Kawidigi Kawasaki Green, White & Black Digital camouflage for that extra custom effect.
Our sport bike wraps are produced using high quality wrapping film with a Glossy or Matte sheet laminate applied over top of the image for that extra added protection. This combination of the two films (wrapping film & sheet laminate)makes this product extra thick 4.75 mil & easier to apply, plus you have the ability to remove the wrap up to 4 years with little to no adhesive residue. Contact us today for your custom sport bike wrap.
Our Customer Brian Large said about his Blue Black flame bike wrap:
Well as you can see i never got around to taking those pictures of my wifes bike. I have been working long hours and so we havent rode for a while. I did however look through some of our pictures we have and found these. The coolest thing about her bike is that the fire on the tank looks like a face. You can clearly see it in the photo. These wraps are easy to do if you take your time with it. The key here is patience ! I am very impressed with your product. hers has been on for over a year now and looks just like it did when we first wrapped it. I would highly recommend this product to anyone wanting to drastically change the appearance of their ride without spending an absolute fortune !
Thanks Pete and Power sports wraps !
Order Blue Black flames here
Shop our wrap selection
See customer bike wrap projects here
Sport Bike wraps can really make the difference in making your bike stand out from the crowd. Imagine pulling in the next bike night on something like this. If you are looking for an inexpensive way to stand out from the crowd we have the product & the look that you want. This bike is owned by Amy Wright & she wanted to make her ZX6 look like no other…. how do you think she did?? An Amazing look with our Punch Metal Plate Purple wrap and it only cost her $325.00 to make her bike look like this, 5 sheets is all you need. If you want to customize your sport bike contact us today…
Shop for bike wraps here…